Eneo DMR-104 Instrucciones de operaciones Pagina 75
- Pagina / 88
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Digital Video Recorder
67
Disk Mirroring
The DVR supports disk mirroring to prevent unexpected loss of recorded video data that might be caused by disk damage
or corruption. You can set up disk mirroring by highlighting Storage in the System menu and pressing the
button.
Figure 53 : System – Storage setup screen.
You can enable mirroring between two disks by designating the source disk and the destination disk from a list of internal
hard disk drives. Up to two Mirrors are supported.
Highlighting the boxes under Source and Dest. and pressing the button allows you to select the source disk and
the destination disk for the selected Mirror.
NOTE: The source disk can be designated only from devices formatted for recording.
A device formatted for archiving cannot be used for disk mirroring.
The manufacturer, model and capacity of the source disk and the destination disk should be same for
the proper mirroring between two disks.
CAUTION: Any existing data on the Destination Disk will be erased once it is designated as a mirror
destination disk.
Highlighting Start and pressing the
button displays a confirmation screen asking you to confirm whether or not you
want to start mirroring the selected disk. Once you start mirroring, the two disks will be resynchronized. Any data on
the destination disk will be erased, and the data on the source disk will be copied to the destination disk. If the source
disk is formatted and has no data, the disks will not be resynchronized. Resynchronization takes about 40 minutes per
each 10GB of capacity. After resynchronization is complete, disk mirroring (writing data on the two disks at the same
time) will start.
NOTE: Resynchronization will pause while searching video.
Once disk mirroring starts, you can cancel it by highlighting Stop and pressing the button. Selecting Stop displays
a confirmation screen asking you to confirm whether or not you want to stop mirroring for the selected disk.
NOTE: Once disk mirroring stopped, the destination disk will be set to Not Used. If resynchronization has been
finished, the destination disk cannot be used for recording or archiving, but it can be used for searching.
If you want to use the disk for recording or archiving, you must reformat it.
CAUTION: Disk mirroring will NOT automatically restart from an interrupted state. Once mirroring
is stopped, you must restart it by following the mirroring setup procedures.
- WARNING 3
- Important Safeguards 4
- Table of Contents 5
- List of Illustrations 7
- Chapter 1 — Introduction 9
- Video Input 11
- Video Loop Through 12
- Factory Reset Switch 12
- HD/SD Out Selector 12
- Network Port 12
- RS232C Port 13
- RS485 Port 13
- Alarm Input/Output 13
- Video Out 14
- Audio In/Out 14
- Power Cord Connector 15
- Chapter 3 — Configuration 16
- Camera Buttons (1 to 16) 17
- Enter Button 17
- Arrow Buttons 17
- Menu Button 17
- Jog Dial, Shuttle Ring 19
- USB Port 19
- ID Button on Remote Control 19
- Turning on the Power 20
- Initial Unit Setup 20
- Setup Screen 21
- System Setup 22
- Date/Time 24
- Account 25
- Storage 27
- Monitoring 28
- Recording Setup 29
- Schedule 31
- Pre-Event 33
- Archive 33
- Network Setup 34
- IP Address 35
- Notification 39
- Event Setup 42
- Alarm-In 43
- Video Loss 44
- Video Blind 44
- Text-In 45
- Alarm-Out 47
- Remote Control 48
- Display Setup 49
- Primary Monitor 50
- Secondary Monitor 51
- Spot Monitor 52
- Status Setup 53
- General 55
- User’s Manual 56
- Chapter 4 — Operation 57
- Live Monitoring Menu 58
- Active Cameo Mode 59
- Zoom Mode 60
- PTZ Mode 60
- Event Monitoring 61
- Covert Camera 61
- Spot Monitoring 62
- Panic Recording 62
- Search Menu 64
- Display 65
- Camera Menu 65
- Event Log Search 66
- Record Table Search 67
- Motion Search 69
- Text-In Search 70
- DISPLAY button and change 71
- Bookmarks 72
- Clip-Copy 72
- Disk Mirroring 75
- Appendix 76
- Text-In Search Examples 77
- WebGuard 78
- Web Monitoring Mode 79
- Web Search Mode 81
- Time Overlap 82
- System Log Notices 83
- Error Code Notices 83
- I/O Connector Pin Outs 84
- RS485 Connector Pin Outs 84
- Map of Screens 85
- Troubleshooting 86
- Specifications 86
- Digital Video Recorder 87
Relacionado con productos y manuales para Grabadores de vídeo digital (dvr) Eneo DMR-104
(51 paginas)
(97 paginas)
(102 paginas)
(48 paginas)
(96 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.085 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales